粗长公司直销MHYBV2X2X0.75批发格通城
更新时间：2025-05-17 22:13:04
价格：4.00每米
品牌:天联牌
销售地区:全国、出口
发货日期:1-3天
联系电话：0316-5961400
联系手机：15075619608
联系人：王艳
让卖家联系我
详细介绍
粗长公司直销MHYBV2X2X0.75批发格通城
本厂主要生产自承式电缆适用于本地电信网的城市与乡镇电信线路，也适用于接入公用网的专用网线路。吊线和电缆用同一外护层，经济实用，安装敷设方便。在一31~C一61~C的环境条件下，自承式电缆的机械和电气性能保持不变。
2、芯数：6芯（3+3）标称截面（主线芯截面：2.5-240㎜²，副线芯截面:0.5-35㎜²）。 天津市电缆总厂第一分厂本着“顾客就是上帝”的原则，以“诚实守信、热情周到”的服务理念赢得了广大客商的信任。
3、低环境温度： ①阻燃聚氯乙烯绝缘和护套：固定敷设－40℃；非固定敷设－15℃； ②氟塑料绝缘和护套：固定敷设－60℃，非固定敷设－20℃。 4、电缆安装敷设温度应不低于0℃。适用于交流额定电压0.6/1KV及以下的行车、台车、传输机械等移动电器用动力传输线及控制、照明、通讯线路，本产品已广泛应用于冶金、电力、船舶、港口等行业。
3、技术指标：聚氯乙烯绝缘电缆长期允许工作温度不超过70℃，电缆的敷设温度应不低于0℃，外径（D）小于25mm电缆的允许弯曲半径，应不小于电缆外径的4倍；外径（D）为25mm及以上的电缆的允许弯曲半径，应不小于电缆外径的6倍。
HJYVP3ZR/SA成束阻燃型聚乙烯绝缘、聚氯乙烯护套、铝塑复合带绕包总屏蔽组合软结构呼叫通信电缆。HJYJVZR/SA成束阻燃型交联聚乙烯绝缘、聚氯乙烯护套、组合软结构呼叫通信电缆。HJYJVPZR/SA成束阻燃型交联聚乙烯绝缘、聚氯乙烯护套、编织总屏蔽组合软结构呼叫通信电缆。
不得使用水、泡沫灭火器灭火。应该使用干黄沙和二氧化碳、干粉灭火器进行灭火。防止身体、手、足、或者使用的消防灭火器等直接与有电部分接触或有电部分过于接近造成触电事故。带电灭火时，还应该带绝缘橡胶手套。充油设备的灭火扑灭充油设备内部火灾时，应该注意以下几点：充油设备外部着火时，可用二氧化碳、121干粉等灭火器灭火；如果火势较大，应立即切断电源，用水灭火。如果是充油设备内部起火，应立即切断电源，灭火是使用喷雾水枪，必要时可用砂子、泥土等灭火。
标记间隔不大于1m；12.其他结构：根据使用场合、用户要求，可提供各种形式的电缆，以满足各种敷设环境条件要求。在一定条件下，也可用于传输2048kbit/s以上的数字信号。。高传输频率分别为30MHz与100MHz。
五：代号名称和含义表2代号代号含义YVF丁腈电缆系列P铜编织屏蔽R多股绞合导体六：主要技术指标1．成品电缆导体(R类)直流电阻(符合GB3956规定)参照附录A表2。2．20℃时绝缘电阻不小于50MΩ/KM。
3、技术指标：聚氯乙烯绝缘电缆长期允许工作温度不超过70℃，电缆的敷设温度应不低于0℃，外径（D）小于25mm电缆的允许弯曲半径，应不小于电缆外径的4倍；外径（D）为25mm及以上的电缆的允许弯曲半径，应不小于电缆外径的6倍。
Flame retardant performance: under specified test conditions, specimen was burning, after removed test of ignition, flame spread only in a limited range, residual flame or residual burning characteristics of self extinguishing reaction in the limited time.
也可提供双层护套的通信电缆。展望未来，任重而道远。公司期待能与新老客户真诚合作不段把握时代脉搏，与时俱进，共创。我厂生产煤矿用阻燃控制电缆,主要规格有MKVV,MKVV22,MKVV32等，各种产品均有《煤安标志》证书，规格齐全，产品广泛应用于各大煤矿系统和煤矿监控系统。
NHA—KVV22适用范围：同NHB—KVV22，用于要求耐火较为苛刻的场所。2、根据协议允许任何长度交货。 一、生产执行标准 采用企业标准。 ③无卤低烟阻燃聚烯烃绝缘和护套：90℃和125℃两种。
变频器接线要求1)变频器和电机的距离应该尽量的短。这样减小了电缆的对地电容，减少干扰的发射源。2)电机电缆应独立于其它电缆走线，其小距离为500mm。同时应避免电机电缆与其它电缆长距离平行走线，这样才能减少变频器输出电压快速变化而产生的电磁干扰。如果控制电缆和电源电缆交叉，应尽可能使它们按90度角交叉。与变频器有关的模拟量信号线与主回路线分开走线，即使在控制柜中也要如此。3)模拟量控制线选用屏蔽线，屏蔽一端接变频器控制电路的公共端(COM)，不要接变频器地端或大地，另一端悬空;动力电缆选用屏蔽或者从变频器到电机全部用穿线管屏蔽，或遵从变频器的用户手册。
Flame retardant cable, is refers to under specified test conditions, specimen was, after removed test of ignition, flame spread only in a limited range, residual sheep and burning in the finite cable to self extinguishing in the course of time. The fundamental characteristic is that it may burn out and not run in the case of fire, but it can spread fire. Generally speaking, in case of electric wire fire, it can be put in the local scope, not to produce spread, keep other kinds of e, avoid causing greater loss. The meaning of the flame retardant cable: under specified test conditions, samples were, in is removed after the fire, the spread of flame on the sample only in a limited range and the characteristic of self extinguishing, which has the ability of or delay the outbreak or spread of flame.
Tianjin cable pull branch factory in line with the principle of "customer is", with "honest, trustworthy, thoughtful" service concept won the trust of the extensive business. I company for the pre-sale, sale, after-sales service promise as follows: 1, in order to deepen the understanding of our company, we welcome you, experts to visit factory, our company will provide accommodation and convenient work. 2. Provide customers with product price information and product information. 3, in order to ensure the products can good, our company adopts domestic high materials, and according to the re of ISO 9001 guarantee system, to strictly control the material purchasing and acceptance, un material is strictly prohibited. 4. Our company strictly implements the system of self-inspection, mutual inspection and special inspection, and it is strictly prohibited to make any substandard semi-products run out of production. To organize the production according to the special technical re of customers and provide products to customers. 5. The wires and cables provided by our company guarantee brand-new, mature and reliable performance and meet the re of customers or customers in all aspects. 6. Our company guarantees that the products provided by us can operate reliably and reliably under normal installation, normal operation and conditions.
本厂主要生产自承式电缆适用于本地电信网的城市与乡镇电信线路，也适用于接入公用网的专用网线路。吊线和电缆用同一外护层，经济实用，安装敷设方便。在一31~C一61~C的环境条件下，自承式电缆的机械和电气性能保持不变。
2、芯数：6芯（3+3）标称截面（主线芯截面：2.5-240㎜²，副线芯截面:0.5-35㎜²）。 天津市电缆总厂第一分厂本着“顾客就是上帝”的原则，以“诚实守信、热情周到”的服务理念赢得了广大客商的信任。
3、低环境温度： ①阻燃聚氯乙烯绝缘和护套：固定敷设－40℃；非固定敷设－15℃； ②氟塑料绝缘和护套：固定敷设－60℃，非固定敷设－20℃。 4、电缆安装敷设温度应不低于0℃。适用于交流额定电压0.6/1KV及以下的行车、台车、传输机械等移动电器用动力传输线及控制、照明、通讯线路，本产品已广泛应用于冶金、电力、船舶、港口等行业。
3、技术指标：聚氯乙烯绝缘电缆长期允许工作温度不超过70℃，电缆的敷设温度应不低于0℃，外径（D）小于25mm电缆的允许弯曲半径，应不小于电缆外径的4倍；外径（D）为25mm及以上的电缆的允许弯曲半径，应不小于电缆外径的6倍。
HJYVP3ZR/SA成束阻燃型聚乙烯绝缘、聚氯乙烯护套、铝塑复合带绕包总屏蔽组合软结构呼叫通信电缆。HJYJVZR/SA成束阻燃型交联聚乙烯绝缘、聚氯乙烯护套、组合软结构呼叫通信电缆。HJYJVPZR/SA成束阻燃型交联聚乙烯绝缘、聚氯乙烯护套、编织总屏蔽组合软结构呼叫通信电缆。
不得使用水、泡沫灭火器灭火。应该使用干黄沙和二氧化碳、干粉灭火器进行灭火。防止身体、手、足、或者使用的消防灭火器等直接与有电部分接触或有电部分过于接近造成触电事故。带电灭火时，还应该带绝缘橡胶手套。充油设备的灭火扑灭充油设备内部火灾时，应该注意以下几点：充油设备外部着火时，可用二氧化碳、121干粉等灭火器灭火；如果火势较大，应立即切断电源，用水灭火。如果是充油设备内部起火，应立即切断电源，灭火是使用喷雾水枪，必要时可用砂子、泥土等灭火。
标记间隔不大于1m；12.其他结构：根据使用场合、用户要求，可提供各种形式的电缆，以满足各种敷设环境条件要求。在一定条件下，也可用于传输2048kbit/s以上的数字信号。。高传输频率分别为30MHz与100MHz。
五：代号名称和含义表2代号代号含义YVF丁腈电缆系列P铜编织屏蔽R多股绞合导体六：主要技术指标1．成品电缆导体(R类)直流电阻(符合GB3956规定)参照附录A表2。2．20℃时绝缘电阻不小于50MΩ/KM。
3、技术指标：聚氯乙烯绝缘电缆长期允许工作温度不超过70℃，电缆的敷设温度应不低于0℃，外径（D）小于25mm电缆的允许弯曲半径，应不小于电缆外径的4倍；外径（D）为25mm及以上的电缆的允许弯曲半径，应不小于电缆外径的6倍。
Flame retardant performance: under specified test conditions, specimen was burning, after removed test of ignition, flame spread only in a limited range, residual flame or residual burning characteristics of self extinguishing reaction in the limited time.
也可提供双层护套的通信电缆。展望未来，任重而道远。公司期待能与新老客户真诚合作不段把握时代脉搏，与时俱进，共创。我厂生产煤矿用阻燃控制电缆,主要规格有MKVV,MKVV22,MKVV32等，各种产品均有《煤安标志》证书，规格齐全，产品广泛应用于各大煤矿系统和煤矿监控系统。
NHA—KVV22适用范围：同NHB—KVV22，用于要求耐火较为苛刻的场所。2、根据协议允许任何长度交货。 一、生产执行标准 采用企业标准。 ③无卤低烟阻燃聚烯烃绝缘和护套：90℃和125℃两种。
变频器接线要求1)变频器和电机的距离应该尽量的短。这样减小了电缆的对地电容，减少干扰的发射源。2)电机电缆应独立于其它电缆走线，其小距离为500mm。同时应避免电机电缆与其它电缆长距离平行走线，这样才能减少变频器输出电压快速变化而产生的电磁干扰。如果控制电缆和电源电缆交叉，应尽可能使它们按90度角交叉。与变频器有关的模拟量信号线与主回路线分开走线，即使在控制柜中也要如此。3)模拟量控制线选用屏蔽线，屏蔽一端接变频器控制电路的公共端(COM)，不要接变频器地端或大地，另一端悬空;动力电缆选用屏蔽或者从变频器到电机全部用穿线管屏蔽，或遵从变频器的用户手册。
Flame retardant cable, is refers to under specified test conditions, specimen was, after removed test of ignition, flame spread only in a limited range, residual sheep and burning in the finite cable to self extinguishing in the course of time. The fundamental characteristic is that it may burn out and not run in the case of fire, but it can spread fire. Generally speaking, in case of electric wire fire, it can be put in the local scope, not to produce spread, keep other kinds of e, avoid causing greater loss. The meaning of the flame retardant cable: under specified test conditions, samples were, in is removed after the fire, the spread of flame on the sample only in a limited range and the characteristic of self extinguishing, which has the ability of or delay the outbreak or spread of flame.
Tianjin cable pull branch factory in line with the principle of "customer is", with "honest, trustworthy, thoughtful" service concept won the trust of the extensive business. I company for the pre-sale, sale, after-sales service promise as follows: 1, in order to deepen the understanding of our company, we welcome you, experts to visit factory, our company will provide accommodation and convenient work. 2. Provide customers with product price information and product information. 3, in order to ensure the products can good, our company adopts domestic high materials, and according to the re of ISO 9001 guarantee system, to strictly control the material purchasing and acceptance, un material is strictly prohibited. 4. Our company strictly implements the system of self-inspection, mutual inspection and special inspection, and it is strictly prohibited to make any substandard semi-products run out of production. To organize the production according to the special technical re of customers and provide products to customers. 5. The wires and cables provided by our company guarantee brand-new, mature and reliable performance and meet the re of customers or customers in all aspects. 6. Our company guarantees that the products provided by us can operate reliably and reliably under normal installation, normal operation and conditions.
相关产品
